SLUDGE JUDGE® - 15 FT. (4.60 M)

4 options available

Product #: C09247

SLUDGE JUDGE® ULTRA - SUPER STRONG

4 options available

Product #: B01386

SLUDGE JUDGE® II EXTENSION SECTION - 5 FT. (1.53 M)

3 options available

Product #: B01357

CASE FOR SAMPLER

Product #: C09249

CLEANING BRUSH - 6 FT. (1.83 M) L. 1 IN. (2.54 CM) DIAMETER BRISTLE

Product #: B01291

CLEANING BRUSH

Product #: B01361

美國Sludge Judge液心取樣器，區授權代理, 上海誠柯檢測設備有限公司

The Sludge Judge® is designed to take accurate readings of settleable solids, 5% or less, in a variety of liquids, to any depth. It is ideal for sewage treatment plants, chemical plants, and food processing facilities - anywhere that accurate sample levels of settleable solids in noncaustic materials are needed. The unit holds approximately 3 oz. per foot (89 ml per 0.31 m). The Sludge Judge® comes in 5 ft. (1.53 m) sections of 3/4 in. (1.90 cm) plastic pipe with screw-type connectors. The top section includes a nylon rope for raising and lowering the sampler. Individual sections can be combined as required to achieve the length needed. Do not use in liquids over 165° F (74° C). Sludge Judge® is not autoclavable. A convenient cotton canvas carrying case that holds four sections, a cleaning brush, cleaning rod, and cotton strips are available.

To use:

1. Slowly lower the Sludge Judge® to the bottom of the tank. The float valve opens (see figure A), allowing materials to flow in. When the bottom has been reached and the pipe has filled to the surface level, tug slightly on the rope as the unit is raised. This sets the check valve(see figure B), trapping the mixture inside.

2. When the unit has been raised clear of the liquid, the amount of solids in the sample can be read using the 1 ft. (0.31 m) increments marked on the pipe sections. To release the material in the unit, touch the pin extending from the bottom section against a hard surface. This opens the check valve to drain the sample. One-year warranty.

Do NOT use for sampling ethanol or ethanol blended fuel. Use Nasco fuel sampler (B01477).

Sludge Judge®可讀取各種液體中5%或以下的可沉降固體至任何深度的讀數。它是理想的污水處理廠，地溝油，廢棄油脂，化工廠，食品加工設施-任何地方都需要準確的樣品水平的沉淀固體在非奧斯汀材料。該裝置的容量約為每英尺3盎司（每0.31米89毫升）。Sludge Judge®有5英尺（1.53米）的3/4英寸截面。（1.90 cm）帶螺紋接頭的塑料管。頂部包括用于提升和降低采樣器的尼龍繩。可以根據需要組合各個部分，以達到所需的長度。不要在溫度過165°F（74°C）的液體中使用。Sludge Judge®不可高壓滅菌。一個方便的棉帆布手提箱，可容納四個部分，一個清潔刷，清潔棒，和棉條。

使用方法：

1. 慢慢地將污泥降到水箱底部。浮閥打開（見圖A），允許物料流入。當?shù)竭_底部且管道已填充至表面水平時，當裝置升起時，輕輕拉動繩索。這就設置了止回閥（見圖B），將混合物困在里面。

2.     2當裝置從液體中取出后，可使用管段上標記的1 ft.（0.31 m）增量讀取樣品中的固體量。要釋放裝置中的材料，請將從底部延伸的銷碰到堅硬的表面。這將打開止回閥以排放樣品。一年保修。

不得用于乙醇或乙醇混合燃料的取樣。使用Nasco燃料取樣器（B01477）。

相關介紹:

1.產品簡介

SLUDGE JUDGE污泥采樣器可采取任何深度的液體中5%或更少的污泥。非常適用于污水處理廠、化工廠、食品加工廠及任何需要在非腐蝕水體中采取沉積物的場合。

污泥采樣器的標準配置為三段長各1.5米、直徑為1.9厘米，帶有螺旋式連接器的透明塑料管。每米大約可容納290毫升樣品。污泥采樣器的頂端部件配有用于提升或降低采樣器的尼龍繩。每個部件能夠組合起來，獲得需要的采樣管長度。配件有帆布袋，清潔刷，棉制清潔布以及鋁制加固桿（采樣管長度過4.6米時必須使用）。配有標準版和加強版可供選擇，加強版采樣管選用聚碳酸酯材料，具有抗沖擊、抗熱畸變性能，而且耐候性好，硬度高的特性。

2.主要特點

獲取沉積固體的準確讀數

采樣管的長度可定制（*小4.6米）